Share your CCIE v5 Written Experience

can any one please send me CCIE dump at khusaiby.assad @ Hotmail.com

@anno @Network Dummy

It is definitely IGMP filtering.

IGMP snooping is a protocol that learns and maintains multicast group membership at the Layer 2 level.

IGMP filtering allows users to configure filters on a switch virtual interface (SVI), a per-port, or a per-port per-VLAN basis to control the propagation of IGMP traffic through the network.

IGMP traffic filters control the access of a port to multicast traffic. Access can be restricted based on the following:

•Which multicast groups or channels can be joined on a port. Channels are joined by IGMPv3 hosts that specify both the group and the source of the multicast traffic.

•Maximum number of groups or channels allowed on a specific port or interface (regardless of the number of hosts requesting service).

•IGMP protocol versions (for example, disallow all IGMPv1 messages).

When you enter an IGMP filtering command, a user policy is applied to a Layer 3 SVI interface, a Layer 2 port, or a particular VLAN on a Layer 2 trunk port. The Layer 2 port may be an access port or a trunk port. The IGMP filtering features will work only if IGMP snooping is enabled (either on the interface or globally).

IGMP filtering is typically used in access switches connected to end-user devices in Ethernet-to-home deployment scenarios.

http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12-2SX/configuration/guide/book/igmpfilt.html

@ Ajax, Thank you for your detailed explanation.

Great. Thanks @Ajax. Now for my other question::

Why shouldn’t this be option C (single topology IS-IS)?
Q 131
Refer to the exhibit.What type of IS-IS is configured on R1?
A.VRF-aware IS-IS
B.multi-process IS-IS
C.single-topology IS-IS
D.IS-IS version 2
Answer:D

I believe it is single topology too. Because, they are asking for type of ISIS configuration.

If you are using IS-IS single-topology support for IPv6, IPv4, or both IPv6 and IPv4, you may configure both IPv6 and IPv4 on an IS-IS interface for Level 1, Level 2, or both Level 1 and Level 2. However, if both IPv6 and IPv4 are configured on the same interface, they must be running the same IS-IS level. That is, IPv4 cannot be configured to run on IS-IS Level 1 only on a specified Ethernet interface while IPv6 is configured to run IS-IS Level 2 only on the same Ethernet interface.

http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6/configuration/15-2mt/ipv6-15-2mt-book/ip6-is-is.html#GUID-76B49B6B-CFEA-47E1-B026-135E526341C7

ISIS Version 2 guidelines cover the features to be covered when implementing the extensions.

The Cisco IOS XR implementation of IS-IS conforms to the IS-IS Version 2 specifications detailed in RFC 1195 and the IPv6 IS-IS functionality based on the Internet Engineering Task Force (IETF) IS-IS Working Group draft-ietf-isis-ipv6.txt document.
The following list outlines key features supported in the Cisco IOS XR implementation:
• Single topology IPv6
• Multitopology
• Nonstop forwarding (NSF), both Cisco proprietary and IETF
• Three-way handshake
• Mesh groups
• Multiple IS-IS instances
• Configuration of a broadcast medium connecting two networking devices as a point-to-point link
• Fast-flooding with different threads handling flooding and shortest path first (SPF).

HI,
ANYONE CAN SHARE CCIE R & S DUMPS??????????? MY EMAIL-ID – {email not allowed}

anyone can suggest which dumps I have to buy for ccie r & s?

Passed today. Spoto is still valid.

Which two commands should you enter to enable IP Source Guard with IP and MAC address filtering
A.ip verify source tracking
B.switchport port-security
C.ip verify unicast source
D.ip verify source
E.ip verify source port-security
Answer:DE for my correct answer is AD. any comments?

@binary
should be B and E

http://packetpushers.net/ccnp-studies-configuring-ip-source-guard/

SW1(config)#int fa0/24
SW1(config-if)#switchport port-security
SW1(config-if)#ip verify source port-security

@ccie123, you mean they have new answers to select ?

6. Which two Cisco Express Forwarding tables are located in the data plane? (Choose two)
a) The label forwarding information base
b) The forwarding information base
c) The label information table
d) The IP routing table
e) The adjacency table

Answer A and B
https://supportforums.cisco.com/discussion/12716301/data-plane-architecture

Q 131
Refer to the exhibit.What type of IS-IS is configured on R1?
A.VRF-aware IS-IS
B.multi-process IS-IS
C.single-topology IS-IS
D.IS-IS version 2
Answer:D
==
I am really confused on this one. C is for sure correct too. I just labbed this with exact same config & did Wireshark capture. This answer is certainly wrong. The IS-IS is setting Version 1 & Version2 also as 1. Does anyone else know a better explanation to decide between C & D?
-PCAP-
Packet: ISO 10589 ISIS InTRA Domain Routeing Information Exchange Protocol (pcap filter: isis)
Version: 1 (pcap filter: isis.version == 1)
Version2 (==1): 1 (pcap filter: isis.version2 == 1)

@CCIEDC2: you mean the answer is B (FIB) & E (Adjacency)? There is obviously no reference of Label FIB (LFIB) in the original cisco ref link either.

Hi All, just got through the written 8xx, Spoto is still valid. All the best for people who are planning to do within next couple of days. Getting ready for the lab 🙂

Hi guys,
I’m planning to take the written exam next week, is there any other dumps shall i study in addition to SPOTO to get the full mark?

thanks for this wonderful community

@Ajax thank you

anyone here to share spoto 222 q vce file please.

hey everyone, i am a DUAL CCIE(R&S, SP) instructor, I give online training for CCIE(SP)written and Lab & CCIE(R&S)written and Lab , i have the verified solutions for all the real labs for CCIE SP AND CCIE-R&S which are used by those people who have already passed and are still passing by using them, the training will be 100% genuine as it is already appreciated by people who are currently taking it and took it in the past. Interested candidates can contact at expert.ccie.4133 at gmail.com

passed with 9xx. good luck

@anmo…
No .. I think they were the same questions with answers, but in my opinion there are other new answers that are obviously wrong … only my perception .. in the end, it is the same test

Which IS-IS metric style is most suitable for MPLS traffic engineering? narrow. but dumps say: wide.
http://www.cisco.com/c/en/us/support/docs/multiprotocol-label-switching-mpls/mpls/13737-mplsteisis.html
any comments?

your link provides the answer: wide

Set up a routing protocol for the MPLS network. It must be a link-state protocol (IS-IS or OSPF). In the routing protocol configuration mode, enter:
For IS-IS:
metric-style wide (or metric-style both)
mpls traffic-eng router-id LoopbackN
mpls traffic-eng [level-1 | level-2 |]

still valid 212Q? thz

Guys passed today 9xx . Spotto 212q is still valid no new questions .

Spoto 212 is still valid.

ISIS overload bit question was also there in the exam.

t.me/rstut

join ccie group on telegram app

rigth thank you @ajax.
Which IPv4 feature prevents multicast joins on a per-port basis? IGMP snooping or IGMP filtering
GPMP snooping.
Answer: IGMP filtering!allows users to configure filters on a switch virtual interface (SVI), a per-port, or a per-port per-VLAN basis to control the propagation of IGMP traffic through the network.

Hey Can someone please pass me the study guide… ive been reading mad books and wouldnt mind working through some of these questions posted below

Much respect
{email not allowed}

@Kilory, scroll back a page or two, there are tons of posts.
@ajax, your awesome for engaging
What ever happen to PL, seems spoto is .. well spot on.
Lastly, am I the only the one studying and using INE here?

@gonnaB-IE please share INE stuff

I will do CCIE wriiten exam next week, can you please provide me CCIE writter at khusaiby.assad @ hotmail.com

Dear All ,

kindly help me CCIE 400-101 V5.1 is Valid or not i shall be very thankfull ???????????

Refer to the exhibit.Which additional configuration statement is required on R3 in order to allow multicast traffic … along the shared-tree?
A.ip mroute 10.4.4.4 255.255.255.255 Tunnel 0
B.ip route 10.4.4.4 255.255.255.255 Tunnel 0
C.ip mroute 192.168.14.0 255.255.255.0 Tunnel 0
D.ip route 192.168.14.0 255.255.255.0 Tunnel 0

any IDEA?

Refer to the exhibit.What type of IS-IS is configured on R1?
A.VRF-aware IS-IS
B.multi-process IS-IS
C.single-topology IS-IS
D.IS-IS version 2
help please

Which two statements about DMVPN with NHRP are true? (Choose two)
A. NHRP shortens the configuration of the hub router.
B.NHRP dynamically provides information about the spoke routers to the hub.
C.NHRP disables multicast
D.The hub router uses NHRP to initiate the GRE tunnel with spokes.
E.The spoke routers act as the NHRP servers.

@ Jermey about IS-IS: Answer:D -> NOK; It’s C

To enable multi-topology is needed: R(c-af)#multi-topology

I don’t find any ISIS V2: The IS-IS protocol was developed in the late 1980s by Digital Equipment Corporation (DEC) and was standardized by the International Standards Organization (ISO) in ISO/IEC 10589. The current version of this standard is ISO/IEC 10589:2002.

update about IS-IS: 2008 RFC5308 adds IPv6 support and RFC5120 adds Multi-Topology Routing support

Hi Guys,
Q171 of Spoto:

When you implement the EIGRP add-path feature, which configuration can cause routing issues on a DMVPN circuit?

a. Disabling ECMP mode under the EIGRP process
b. disabling automatic summarization
c. enabling next-hop-self under the process
d. enabling synchronization under the EIGRP process
e. disabling default variance under the EIGRO process
f disabling NHRP when deploying EIGRP over DMVPN.

Spoto correct answer is reported to be E.
But, don’t you think that also C is a valid answer? I mean, by default when you configure EIGRP with add-paths in DMVPN you have to disable next-hop-self and not touch variance to not cause troubles… what is your opinion? Why E should be the valid answer?

Source:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_eigrp/configuration/xe-3s/ire-xe-3s-book/ire-add-path.html

anyone here to share spoto 222 q vce file please.

rd what is 222q? is it 212q?

Excuse me, you’re right. Would you please provide a useful download path?

in PL web, 222 Q&A Updated: Mar 12, 2017 :/

@ WisdomSt I agree with you. This question is a little bit strange, because the next-hop-self is enabled by default, so you don’t have to enable it, and the variance is not disabled, it can be changed, right?

Passed it today with examunion version. You also can get http://www.examunion.com/400-101.html

Yeah!

Finally passed my ccie 400-101 test yesterday afternooon!

It seems no new Qs appeared in my 400-101 test, not 100% sure, but all questions were from that passleader 400-101 dumps (-222q-), the most valid dumps now~!

~~~

Good Luck!

Here you can review part of that PL 222q dumps: http://www.dumps4share.com/?s=400-101

Good Luck!

Passed Yesterday … Score 850 , pass from 804

SPOTO 222 is still valid … it has some wrong answers, but all is good

one new question for Overload bit

Guys, passed today 8xx. Spotto 212q is still valid.

Guys, IS Spoto 212q is still valid ?????

i will pass next Monday
please I need ADVICE….