Share your CCIE v5 Written Experience

@Anonymous

I would say B. Besides, it is not true that both routers have to communicate via TCP 179.. This port appears on just one router in the peering.

Is there any other question on 103q that is wrong or with ambiguity? Lets discuss

@ hi all

i’ve just come now , i’ll check the emals an reply them all.

@ Emery
thank you for sendind me the 103Q dump

i’ll upload this new dump and send it for all who wants FOR FREE 🙂
good luck

@GKK
It is of-course flooded to an Area not AS domain..Generated by ABRs not ASBRs. be careful of this confusion or trick

Area* is the right answer

@GKK

I would said flooded throughout AS, since LSA should reach every router in AS (except in originating area). I agree that the wording of question is unclear, but I will choose AS (instead of area)

@GKK

Also, for question about “..built in policer…” I will choose priority percent. I discussed with some coleagues and they agreed that question is unclear, but because of “policer” word I guess creator of the question whant to check out knowledge about difference between priority and bandwidth command.

@Tim

“LSA should reach every router in AS (except in originating area)”. Agree with word “reach”, but it will not be the always the original lsa from the abr attached to the area where ASBR belongs.
Consider that the abr floods lsa-4 in area0. another abr in area0 (connected to a distinct area) should send another lsa-4 in its area in order for the routers of this area to be able to use is as an exit point towards the asbr.

@GKK

I know that both of us understand how LSA flooding occur 🙂 I quess I will choose this answer and we shall see what will happened on the exam 🙂

I scheduled my for 16.1., so I let you know what are the results.

Previous comment is mine, but I did not put the name by mistake.

Which PIM feature allows the same multicast group address to be reused in different administrative domains?
A. Proxy Registering
B. IP Multicast Helper
C. IP Multicast Boundary
D. CGMP

I would say C. According to Cisco, when a boundary is set up, no multicast data packets are allowed to flow across the boundary from either direction. The boundary allows the same multicast group address to be reused in different administrative domains.

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/37e/multicast/configuration_guide/b_mc_37e_3850_cg/b_mc_3e_3850_cg_chapter_011.html

Your view?

passed yesterday with score 96x

BGP best path selection criteria
ipv6 to Ipv4 , MPLS PHP

Remove*** F0R FREE DUMPS
https:/*/goo.gl/rVKaJH

Please put following items into “EEM Applet” and “EEM Script”
1. A policy written in TCL
2. Defined offline and copied to the device
3. Registered only when an event is specified
4. Supports events without action
5. Supports keyword extensions for developing policies
6. Supports only one event: configuration command in its configuration

My answer:

“EEM Script” – 125,
A policy written in TCL
Defined offline and copied to the device
pports keyword extensions for developing policies

“EEM Applet” – 346
Registered only when an event is specified
Supports events without action
Supports only one event: configuration command in its configuration

@Ebrahem
Please can forward me the dump rochellemari at gmail.com

Appreciate it

@ thilinapm
@ likhit52
@ DanielPasono
@ a.jawad.s
@ GabrieleCaruso
@ aboalba
@ NathanialAdams
@ goforccie5
@ {email not allowed}
@ {email not allowed}
@ {email not allowed}
@ {email not allowed}
@ {email not allowed}
@ {email not allowed}
@ {email not allowed}
@ {email not allowed}
@ goforccie5
@ mariusz.walocha
@ just1ccie
@ almistroo88
@ cciersproject2019
@ tyson.lance7
@ koragodimaubsuk
@ redparadise06
@ rochellemari

check your emails 🙂

I’ve sent all the dumps i have , (102q,106q,126q , 250q , 268q , 100q , 103q ) wich i’ve used to pass the exam.along with the new one 100Q dates on 2019-1 and the 103Q which some friend has sent me.
so these all the dumps available right now

all the dumps almost contain same questions, the new dumps may contian some new questions , i advice to start buy 268q , then when study the other dumps it will be like a revision and know the new questions.
its not enough to study the latest dumps only 100q nor 103q , study them all.

note that there are WRONG answers in all of those dumps , try to check them yourself, I’ve uploaded what i’ve checked myself , i didnt check all the dump. i hope that would help.

I advice to keep checking the rstut.com for the new quesions because i see some of the new questions i’ve got in my exam.

dont hesitate and go take the exam .
also dont believe who says the dumps are changed, because the dumps will not changed at all , but Cisco adds a new questions to the same dump from time to time, so study those dumps and the new questions.

also dont believe who says the dump is 100% valid ,because there is no 100% valid dump !! you always will find new questions in each exam.

i’ll not post links here again to dont give the spammer a chance to cheat people and use my name as they already did.

i’ll keep sending the dumps FOR FREE

anyone wants the dumps just write his email here or send it to my email.

Good luck

@ thilinapm
@ likhit52
@ DanielPasono
@ a.jawad.s
@ GabrieleCaruso
@ aboalba
@ NathanialAdams

check your email 🙂

good luck

Hi @Ebrahem

Please send to me the latest dump again
jun0602 @ live com my

thanks alot

Hi guys ,

When is MAC authentication bypass enabled by default?
A. When two-factor authentication is configured.
B. After 802.1x authentication verifies the client’s identity.
C. When 802.1x authentication fails.
D. When 802.1x authentication times out.

what is the right answer here B or D

@Help

for me C and D are right answers,but there can be only one, so I am not sure, which one is right.

Dear @Ebrahem

Please send to me the latest dump too

chjhnav @ gmail . com

thanks a lot!

@Help! & Tim
I agree with Tim.
Just in order to conclude somehow I think that auth failure will definitely enable MAB since:

When configured as a fallback mechanisms, MAB is deployed after IEEE 802.1X times out. If the endpoint’s Pre-eXecution Environment (PXE) process times out, or if Dynamic Host Configuration Protocol (DHCP) gets deep into the exponential backoff process before the timeout occurs, the endpoint may not be able to communicate even though the port has been opened. To the end user, it will appear as if network access has been denied.

For chatty devices that send a lot of traffic, MAB will be triggered shortly after IEEE 802.1X times out. But for quiet devices, or for devices that have gone quiet because, for example, the DHCP client timed out before IEEE 802.1X did, MAB may not occur for some time.

What do you think?

Passed the 400-101 exam TODAY! 9xx/1000 POINTS!

Only learned that NEW PassLeader 400-101 dumps with 103 Q&As.

Still 100% accurate, all questions were from PL, valid enough for passing!

Trying the PassLeader 400-101 dumps ASAP, all guys!

Good luck!!

@Ebrahem could you please send me me the the collection of the dumps you were able to collect to: honza.ccie @gmail.com

@ Emery
@GKK

Please share the 103q pass leader dumps with me on
kaybeejnr @ gmail com

Thanks you guys!

@ kaybeejnr
@ honza.ccie
@ chjhnav
@ jun0602
@ ccll9877

check your email 🙂

good luck

@Ebrahem

Please send to me the latest dump 103q pass leader dumps too.

alireza_3991 @ yahoo . com

thanks.

@Ebrahem thanks a lot!

@Ebrahem
Please can you forward me the dump ponssecobra at gmail.com

thanx in advance
Appreciate it

Hello again,

Which feature must be enabled so that an IS-IS single topology can support IPv6 traffic?
A. New-style TLVs only
B. Adjacency checking
C. Old-style TVLs only
D. Extended metrics
E. Both new-and old-style TLVs

I am between D & A. What do you think?

====

Which two statements about route summarization are true?
A. It can be disabled in RIP, RIPv2, and EIGRP
B. EIGRP and RIPv2 route summarization are configured with the ip summary-address command under the route process
C. EIGRP can summarize routes at the classful network boundary
D. RIPv2 can summarize routes beyond the classful network boundary

Which one is correct? Could you pls send a reference/source to study this?

==

RIPv2 automatically summarizes IPv4 routes on classful boundaries. Which boundaries does it use for automatic summarization of IPv6 routes?
a. IPv6 is classless and automatic summarization is not done.
b. Automatic summarization of IPv6 routes is disabled bu default and the boundaries must be specified when it is enabled
c. Automatic summarization of IPv6 routes is done at the 32 bits, 48 bits, 64 bits boundaries
d. IPv6 routes are automatically summarized on octet boundaries.

Which is the correct?

Another discrepancy ..

Refer to the exhibit. If router R1 sends traffic marked with IP precedence 3 to R2’s Loopback address.Which class would the traffic match on R2’s Gi1/0 interface?

af31 or default and why?
==

@ alireza_3991
@ ponssecobra

check your email 🙂

good luck

Hi @Ebrahem
Kindly share the dumps with me at barsoom1980*@*gmail com

Thank you

Hi @Ebrahem
Kindly share the dumps with me at barsoom1980*@*gmail com

Thank you

Hi,

Please share latest dump in {email not allowed}.
Thanks

Hi,

Please share latest dump in prabhatrahul*@*Yahoo com.

Thanks

@ prabhatrahul
@ barsoom1980
@ ccienzir
@ jorge.moreno.cuenca

check your email 🙂

good luck

Please help Answer this Question

Which design is ideal when migrating from traditional network to SD access Architecture
A. Dual Links
B. Collapse Core/Aggregation Design
C. Traditional Three Tier Hierarchical Network
D. U-Topology
E. Routed Access

One Dump says C another one E. Your View?
i am confused

Hi Ebrahem,

Please could you share the dumps with me janlevi88*@*gmail com

Thank you

@GKK
Please go through this topic about LSA Type 4, it is explained very detailed and easier

http://www.astorinonetworks.com/2011/06/06/understanding-ospf-type-4-lsas/

The ABR since it is in the same area with the ASBR and directly connected is responsible to advertise the route to the ASBR to other routers in a different area. The ABR has 1 interface connected to 1 area (Area 0) and the other to another area (Area 25)

@ janlevi88
@ elrmanu

check your email 🙂

good luck

Hi Ebrahem,
please send to joker5611 at gmail.com

Many thanks in advance,

@ Ebrahem

Thanks a lot!!

And i am not “JJ” above…

@Ebrahem
Please send to me the latest dump too
eadgwind @ gmail . com

thanks.

@Ebrahem
Please share the lasted dumps with me too.
bhupendra.chauhan11 gmail com

need dumps , please assist .. Email rizwan.cyber @ gmail.com

H o o o o
Oh o o o o
Oh o o o o
Oh o o o o
Teri akhiyon ka waar jaise sher ka shikar
Tera husn dhueydaar jaise jaltaa cigar
Teri akhiyon ka waar jaise sher ka shikar
Tera husn dhueydaar jaise jaltaa cigar
Tere pyar ka nasha kabhi aar kabhi paar
Tera pyaar pyaar pyaar hookah bar
Tera pyaar pyaar pyaar hookah bar
Tera pyaar pyaar pyaar hookah bar bar bar
Tera pyaar pyaar pyaar hookah bar
Oh o o o o
Oh o o o o
Oh o o o o
Oh o o o o
Tera pyaar pyaar pyaar hookah bar
Tera pyaar pyaar pyaar hookah bar
Tera pyaar pyaar pyaar hookah bar bar bar
Tera pyaar pyaar pyaar hookah bar
Tu jo naa ho mere rubaru
Bin tere jeene se main daru
Hai yehi tamanna meri bas tere liye jiyu maru
Tera huya jo deedar baaje dil mein sitaar
Tera husn dhuyedaar jaise jaltaa cigar
Tere pyar ka nasha kabhi aar kabhi paar
Tera pyar pyar pyar hookah bar
Tera pyar pyar pyar hookah bar
Tera pyar pyar pyar hookah bar bar bar
Tera pyar pyar pyar hookah bar
Oh o o o o
Oh o o o o
Oh o o o o
Oh o o o o
Jaage hum yunhi raat bhar
Hai hawaaon main awaargi
Yeh kashish yeh deewangi
Hai tujhi se meri trishnagi
Hai junnon ye sawaar main to bhoola sansaar
Tera husn dhueydaar jaise jaltaa cigar
Tere pyar ka nasha kabhi aar kabhi paar
Tera pyar pyar pyar hookah bar
Tera pyar pyar pyar hookah bar
Tera pyar pyar pyar hookah bar bar bar
Tera pyaar pyaar pyaar hookah bar
Tera pyaar pyaar pyaar hookah bar
Tera pyaar pyaar pyaar hookah bar bar bar
Tera pyaar pyaar pyaar hookah bar
Oh o o o o
Oh o o o o
Oh o o o o
Oh o o o o

Please share the latest dumps at lybtas()gmail.com

Passed the 400-101 exam TODAY! 9xx/1000 POINTS!

Only learned that NEW PassLeader 400-101 dumps with 103 Q&As.

Still 100% accurate, all questions were from PL, valid enough for passing!

Trying the PassLeader 400-101 dumps ASAP, all guys!

Good luck!!

@Noriyuki Sato

Congrats!

Would you like to share that 103q PassLeader 400-101 dumps with me?

Mark Baldino @ nifty com

Thanks a lot!

Refer to the exhibit. When it attempted to register the EEM script, the device returned this error message. Which action can you take to correct the problem?
A. Configure the event action to run the applet.
B. Configure the event manager run command to register the event.
C. Configure the event none command so that the event can be triggered manually.
D. Configure the end command at the end of the BACKUP EEM policy.

What is the problem and which action is the correct one?

Hi @Ebrahem
Send me 103Q@A to doctoralban(*)yahoo.com please.
Thank you in advance!